Journal of biomechanics
-
Journal of biomechanics · Mar 2018
A combined passive and active musculoskeletal model study to estimate L4-L5 load sharing.
A number of geometrically-detailed passive finite element (FE) models of the lumbar spine have been developed and validated under in vitro loading conditions. These models are devoid of muscles and thus cannot be directly used to simulate in vivo loading conditions acting on the lumbar joint structures or spinal implants. Gravity loads and muscle forces estimated by a trunk musculoskeletal (MS) model under twelve static activities were applied to a passive FE model of the L4-L5 segment to estimate load sharing among the joint structures (disc, ligaments, and facets) under simulated in vivo loading conditions. ⋯ Therefore, as an alternative approach to represent in vivo loading conditions in passive FE model studies, this FL can be estimated by available in-house or commercial MS models. In clinical applications and design of implants, commonly considered in vitro loading conditions on the passive FE models do not adequately represent the in vivo loading conditions under muscle exertions. Therefore, more realistic in vivo loading conditions should instead be used.
-
Journal of biomechanics · Mar 2018
Biomechanical response of intact, degenerated and repaired intervertebral discs under impact loading - Ex-vivo and In-Silico investigation.
Understanding the effect of impact loading on the mechanical response of the intervertebral disc (IVD) is valuable for investigating injury mechanisms and devising effective therapeutic modalities. This study used 24 porcine thoracic motion segments to characterize the mechanical response of intact (N = 8), degenerated (Trypsin-denatured, N = 8), and repaired (Genepin-treated, N = 8) IVDs subject to impact loading. A meta-model analysis of poroelastic finite element simulations was used in combination with ex-vivo creep and impact tests to extract the material properties. ⋯ It is concluded that the disc time-dependent response significantly changes with disc degeneration. Cross-linker Genipin has the potential to recover the hydraulic permeability and can potentially change the time dependent response, particularly in the IDP. This is the first study, to our best knowledge, which explores the effect of impact loading on the healthy, degenerated and repaired IVD using both creep and impact validation tests.
-
Journal of biomechanics · Mar 2018
Thoracolumbar spine loading associated with kinematics of the young and the elderly during activities of daily living.
Excessive mechanical loading of the spine is a critical factor in vertebral fracture initiation. Most vertebral fractures develop spontaneously or due to mild trauma, as physiological loads during activities of daily living might exceed the failure load of osteoporotic vertebra. Spinal loading patterns are affected by vertebral kinematics, which differ between elderly and young individuals. ⋯ The maximum compressive loads predicted for the elderly motion patterns were lower than those of the young for L2/L3 and L3/L4 lumbar levels during flexion and for upper thoracic levels during stand-to-sit (T1/T2-T8/T9) and sit-to-stand (T3/T4-T6/T7). However, the maximum loads predicted for the lower thoracic levels (T9/T10-L1/L2), a common site of vertebral fractures, were similar compared to the young. Nevertheless, these loads acting on the vertebrae of reduced bone quality might contribute to a higher fracture risk for the elderly.
-
Journal of biomechanics · Mar 2018
Load-sharing in the lumbosacral spine in neutral standing & flexed postures - A combined finite element and inverse static study.
Understanding load-sharing in the spine during in-vivo conditions is critical for better spinal implant design and testing. Previous studies of load-sharing that considered actual spinal geometry applied compressive follower load, with or without moment, to simulate muscle forces. Other studies used musculoskeletal models, which include muscle forces, but model the discs by simple beams or spherical joints and ignore the articular facet joints. ⋯ The disc forces and moments were determined using equilibrium equations, which considered the applied loads, including muscle forces and IDP, as well as forces in the ligaments and facet joints predicted by the FE model. Load-sharing was calculated as the portion of the total spinal load carried along the spine by each individual spinal structure. The results revealed that spinal loads which increased substantially from the upright to the flexed posture were mainly supported by the discs in the upright posture, whereas the ligaments' contribution in resisting shear, compression, and moment was more significant in the flexed posture.
-
Journal of biomechanics · Mar 2018
Computational study of the role of fluid content and flow on the lumbar disc response in cyclic compression: Replication of in vitro and in vivo conditions.
The intervertebral disc viscoelastic response is governed primarily by its fluid content and flow. Invivo measurements demonstrate that the disc volume, fluid content, height and nucleus pressure completely recover during resting even after diurnal loading with twice longer duration (16 vs. 8 h). In view of much longer periods required for the recovery of disc height and pressure in vitro, concerns have been raised on the fluid inflow through the endplates that might be hampered by clogged blood vessels post mortem. ⋯ The model with free inflow increased segment height and nucleus pressure while the model with no fluid inflow resulted in a relatively small recovery in segment height and a rather constant nucleus pressure during unloading periods. Results highlight an excessive mobile fluid content as well as a restricted fluid inflow through endplates as likely causes of the discrepancies between in vivo and in vitro studies. To replicate in vivo conditions in vitro and in silico, disc hydration level should be controlled by adequate selection of preload magnitude/period and/or mobile fluid porosity.