• Spine J · Nov 2013

    Lumbar facet joint and intervertebral disc loading during simulated pelvic obliquity.

    • John M Popovich, Judson B Welcher, Thomas P Hedman, Wafa Tawackoli, Neel Anand, Thomas C Chen, and Kornelia Kulig.
    • Division of Biokinesiology and Physical Therapy, University of Southern California, 1540 E. Alcazar St, CHP-155, Los Angeles, CA 90089, USA; Spine Biomechanics and Tissue Engineering Laboratory, Cedars-Sinai Medical Center, 8700 Beverly Blvd., Davis Building, 6006, Los Angeles, CA 90048, USA. Electronic address: popovi16@msu.edu.
    • Spine J. 2013 Nov 1; 13 (11): 1581-9.

    Background ContextIntervertebral disc and facet joints are the two primary load-bearing structures of the lumbar spine, and altered loading to these structures may be associated with frontal plane spinal deviations.PurposeTo determine the load on the lumbar facet joint and intervertebral disc under simulated frontal plane pelvic obliquity combined loading, an in vitro biomechanical study was conducted.Study Design/SettingAn in vitro biomechanical study using a repeated-measures design was used to compare L4-L5 facet joint and intervertebral disc loading across pure moment and combined loading conditions.MethodsEight fresh-frozen lumbosacral specimens were tested under five loading conditions: flexion/extension, lateral bending, axial rotation using pure moment bending (±10 Nm), and two additional tests investigating frontal plane pelvic obliquity and axial rotation (sacrum tilted left 5° and at 10° followed by a ±10-Nm rotation moment). Three-dimensional kinematics, facet load, and intradiscal pressures were recorded from the L4-L5 functional spinal unit.ResultsSagittal and frontal plane loading resulted in significantly smaller facet joint forces compared with conditions implementing a rotation moment (p<.05). The facet joint had the highest peak load during the 10° combined loading condition (124.0±30.2 N) and the lowest peak load in flexion (26.8±16.1 N). Intradiscal pressure was high in lateral flexion (495.6±280.9 kPa) and flexion (429.0±212.9 kPa), whereas intradiscal pressures measured in rotation (253.2±135.0 kPa) and 5° and 10° combined loading conditions were low (255.5±132.7 and 267.1±127.1 kPa, respectively).ConclusionsFacet loading increased during simulated pelvic obliquity in frontal and transverse planes, whereas intradiscal pressures were decreased compared with sagittal and frontal plane motions alone. Altered spinopelvic alignment may increase the loads experienced by spinal tissue, especially the facet joints.Copyright © 2013 Elsevier Inc. All rights reserved.

      Pubmed     Full text   Copy Citation     Plaintext  

      Add institutional full text...

    Notes

     
    Knowledge, pearl, summary or comment to share?
    300 characters remaining
    help        
    You can also include formatting, links, images and footnotes in your notes
    • Simple formatting can be added to notes, such as *italics*, _underline_ or **bold**.
    • Superscript can be denoted by <sup>text</sup> and subscript <sub>text</sub>.
    • Numbered or bulleted lists can be created using either numbered lines 1. 2. 3., hyphens - or asterisks *.
    • Links can be included with: [my link to pubmed](http://pubmed.com)
    • Images can be included with: ![alt text](https://bestmedicaljournal.com/study_graph.jpg "Image Title Text")
    • For footnotes use [^1](This is a footnote.) inline.
    • Or use an inline reference [^1] to refer to a longer footnote elseweher in the document [^1]: This is a long footnote..

    hide…